For work, you will need not very transparent white, yellow, blue, and e fabrics, a general drawing of the product and an auxiliary drawing with separate details for the postcard; yellow background detail and details of flowers and leaves.
On the glass of the light table, place an auxiliary pattern, on the pattern - a well-smoothed yellow fabric (face up). Turn on the device for burning through the tissue and select the operating temperature on the needle for cutting the yellow fabric: set the handle of the resistor to the minimum temperature and stepwise increase the heating of the needle, make test cuts on the fabric, carving small pieces and trying to stick to the tracing paper. If the cutting of the clean, through and the parts to the ring stick well (by simply pressing the pads of the finger they can not be moved from the tracing paper), the fabric does not become scorched along the cutting line, then consider that the temperature of heating the needle to obtain a qualitative cut for this particular tissue is selected and cut out the product.
Do you plan to relax on the stunning Seychelles and enjoy the sights? Book tours to tourskidki.ru and you are guaranteed a carefree vacation.
But before fixing the flap of fabric on the tracing paper underneath: smooth the fabric over the pattern with your hand, make short cuts (4-5 mm) at intervals of 10-20 mm, stepping back 0.5-1 cm from the border of the pattern. Each cut is immediately very fast (!) Press with your finger. Make cuts by placing the needle tip between the index and middle fingers, which are spread out like a “V” sign and press the fabric in place of the cut to the tracing paper.
On the glossy fabric fixed on the tracing paper, there should be no wrinkles, hauling diagonally - the fabric should fit snugly to the tracing paper throughout the entire pattern.
Turn on (if necessary) the backlight under the table. With the fingers of your left hand, spread out the letter "V" 4-5 cm, press and even slightly stretch the fabric on the tracing paper across the direction of the cut. Lower the tip of the needle between your fingers and cut the festoons, leaving no cut threads in the corners of the pattern. The right hand (brush) makes only small movements, moving the needle along the pattern, and the left hand presses and pulls the fabric and moves the pattern across the glass towards the needle (left, right or in a circle).
Cut out the yellow detail for the background. Cotton flap wipe the hot needle, put the pencil with the needle in the holder, turn off the device with the local button on the panel.
Blade (blunt side) with a cut yellow piece from the tracing paper and set aside.
On the same auxiliary pattern, lay a blue cloth (face up). Turn on the device and, just like for the yellow fabric, select the working temperature on the needle. For cutting out small parts, fixing the cloth on the tracing paper is not necessary, it is enough to hold and stretch the fingers of the left hand over the cut out detail of the picture. Cut the blue parts, remove them from the tracing paper with a blade, move aside and cut the following (again) - repeat the steps until you have cut the required number of blue parts.
Remove the blue parts from the glass. On the drawing, put a green cloth and the current is the same as for a blue fabric, select the temperature and cut out the desired number of leaves.
Place a basic pattern on the glass, a white cloth ironed on it (face up).
Turn on the device, select the working temperature on the needle and fix the fabric on the tracing paper with cuts around the frame.
Cut the rectangular frame. Put the ruler on the pattern and cut the fabric, warming the needle every 2-3 cm for 20-30 seconds.Cut out a rectangle and remove the excess white fabric from the tracing paper: with your left hand, press the fabric near the cut (inside the rectangle), and with your right hand move the fabric behind the rectangle, making sure that there are no undercut, and if they are, cut them with a hot needle.
Place a yellow detail on the white rectangle, align it with the pattern. Turn on the device and fix the yellow part on the white part with rare points.
Helping yourself with a sewing needle, spread out the blue and green details according to the drawing. Turn on the device and, holding tweezers with sharp tips on every detail of the colors, weld a large dot 1 - 1.5 mm in diameter (with a needle tip, scroll through three layers of tissue). Attach the leaflets with a deep cut (to white tissue), starting from the base of the leaflet and gradually withdrawing the needle from the tissue to the middle of the leaflet. With cut-strokes, mark the branches along the pattern and through holes-droplets-very small leaves. Remove the postcard from the tracing paper.
New Year Topiary Fir-tree
7 signs of a schoolboy’s properly designed room: Mobilikaz’s salon tells
Spider Crochet Application
Unusual recipes for chocolate manna
How to make homemade sausages
How easy it is to make skeleton leaves
Brush from plastic bottles
Designer Tips: 25 Important House Design Secrets