New technology of warming floors by penokleksom

If you started a repair, and still have not decided what material to use for the floor, this article will be useful for you. In it, we will consider an inexpensive, but at the same time having a lot of advantages, the method of floor insulation using penoplex. Recently, it is often used in construction, including in the manufacture of floors. It is worth mentioning this material briefly. Unlike polyfoam, it is more durable, has higher thermal conductivity, vapor permeability, zero water absorption, and resistance to microorganisms. All these properties make this material suitable for floor insulation.

Floor insulation with foam plastics

So, first you need to dismantle old floors - linoleum, parquet, etc. In apartments, the base of the floor is screed and concrete, and in private houses it can be wooden boards. If both are in good condition, then you should not change anything.The illustration shows an example of a private house where the floors are wooden, but they were in good condition. In the event that the wood is rotten, the floors must be removed and the screed should be poured with concrete. In the apartments everything will be much easier. Most often just remove the damaged cover, then you can begin to insulate. If the floors are wooden, you can further scroll them with screws to the lower beams, as over time the nails could weaken the mount. This is so that they do not creak.
New technology of floor insulation penoplex
Calculate how much material you need. Since the sheets of penoplex are different in size, calculate the square of the floor of the room, and already in the hardware store you can determine how many sheets are needed. The same is true of OSB.
New technology of floor insulation penoplex
Next, you need to select the highest point (angle) in the room, and start laying the floor from it. This can be determined by the building or laser level. At the highest point, the layer of foam should be minimal. At the corners of the wall and floor, it is necessary to go through the mounting foam for waterproofing.Next, the mounting foam is applied to the floor surface, after which a sheet of Penoplex is placed on it. With the help of the construction level it is necessary to level the sheet gently tapping on it with your hand. Before applying the foam, you can slightly moisten the floor with water so that the dust does not repel the foam. If the height of the ceilings allows, and you have the opportunity to raise the floor, then as a leveling of the floor surface you can use wooden slats 2-3 cm thick. The slats are screwed to the floor level, and between them is a series of penoplex.
New technology of floor insulation by penokleksom
New technology of floor insulation by penokleksom
New technology of floor insulation by penokleksomNew technology of floor insulation by penokleksomNew technology of floor insulation by penokleksomNew technology of flooring foam insulation
New technology of floor insulation penoplex
New technology of floor foam insulation Thus, the next sheets of Penoplex are also laid down. Cut this material with a conventional construction knife. You will also need a tape measure to measure the dimensions that need to be cut off. It is best to use a special gun for foam, as it will be economical. If you use ordinary cylinders with foam, then opening it, you must use it immediately, otherwise it will solidify. The gun can be used for several days. "style =" max- width: 100%; " alt="New technology for warming floors with foam"> After you lay the sheets of penoplex, and the foam on which you plant them, it will harden, you need to fix the foam plack to the bottom wooden floor with screws. It is better to use screws longer. Before screwing the screw, drill holes with a drill. However, do not need to tighten the screw completely. These self-tapping screws must be screwed on. All the screws must be twisted in a row with an indentation of 20 - 30 cm. The OSB plate will then fall on them.
New technology of flooring foam insulation
New technology of flooring foam insulation
New technology of floor foam insulation
When all the screws are twisted, foam panels also need to go through the foam, including around the screws, and put a sheet of RSD on top. Thus, he lies on the caps of the screws and the foam, which, when hardened, will hold the plates.
New technology of flooring foam insulation
New technology of flooring foam insulation
New technology of flooring foam insulation
After that, you need to wait a little until the foam hardens, and then re-tighten the screws to the OSB plates to fasten them. The indent when tightening the screws should be 20-30 cm. The OSB should be fixed with the waterproof side up.
New technology of floor insulation penoplex
New technology of flooring foam insulation
New technology of flooring foam insulation
New technology of floor insulation penoplex
The advantages of this technology of floor installation and insulation are that it is not an expensive method. It is much cheaper than using concrete to fill the screed. Also laying of such floor is carried out a maximum in one day if the room has the usual sizes. If necessary, such floors are easy to dismantle.

Related News:


Bezel with chamomile and rosehip
A simple flasher on one transistor
Master doll house
Do-it-yourself headphone cases
Chest - a convenient locker for the whole family
Why do we want to cry
Festive New Year Manicure 2013 (25 photos)
Skewer Case